[+] Nie działa karta WiFi Intel 5100

szcz00ri - 19-11-2009 16:32
Witam.

Podłącze się do tematu.

Laptop Lenovo IdeaPad G9550.

Nie mam pojęcia jak zainstalować bezprzewodową kartę sieciową.
lspci 04:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection
07:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02) ifconfig eth0 Link encap:Ethernet HWaddr 00:26:22:05:14:a4
inet addr:192.168.0.93 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::226:22ff:fe05:14a4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2247 errors:0 dropped:0 overruns:0 frame:0
TX packets:2450 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1690674 (1.6 MiB) TX bytes:481695 (470.4 KiB)
Interrupt:17

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:52 errors:0 dropped:0 overruns:0 frame:0
TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3280 (3.2 KiB) TX bytes:3280 (3.2 KiB) i tu jest problem:
iwconfig lo no wireless extensions.

eth0 no wireless extensions. korzystam z wicd internet kablem ładnie mi widzi, nie muszę nic konfigurować

Kilka godzin "googlowania" i nie znalazłem nic konkretnego. Większość postów dotyczy konfiguracji internetu bezprzewodowego zakładając, że są sterowniki do karty bezprzewodowej zainstalowane.

Zainstalowałem również: bcm5700-source ale nie znalazłem nigdzie jak to wrzucić do uruchamianych modułów, może w tym jest moja niewiedza.

Zainstalowane również: wireless-tools Proszę o podpowiedź jak rozwiązać ten problem.

AdeBe - 19-11-2009 17:13
szcz00ri, wydzieliłem twój post z poprzedniego tematu.
Nie "podpinaj się" pod tematy nie związane bezpośrednio z twoim problemem. Szczególnie, gdy taki temat nie jest najświeższy.

Pakiet bcm5700-source raczej nie jest Ci potrzebny.
Masz kartę WiFi Intela, sprawdź czy masz zainstalowany pakiet firmware-iwlwifi Jeśli nie, to zainstaluj i zrestartuj komputer.
Jeśli nadal nie będzie działało lub masz ten pakiet zainstalowany, to wklej wynik polecenia dmesg Aha, byłbym zapomniał: podaj wersję Debiana i kernela.

szcz00ri - 19-11-2009 18:06
Wstyd, nie znać swojego sprzętu.

dmesgg [ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 20:45:37 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bdaa1000 (usable)
[ 0.000000] BIOS-e820: 00000000bdaa1000 - 00000000bdaa7000 (reserved)
[ 0.000000] BIOS-e820: 00000000bdaa7000 - 00000000bdbba000 (usable)
[ 0.000000] BIOS-e820: 00000000bdbba000 - 00000000bdc0f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bdc0f000 - 00000000bdd08000 (usable)
[ 0.000000] BIOS-e820: 00000000bdd08000 - 00000000bdf0f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bdf0f000 - 00000000bdf19000 (usable)
[ 0.000000] BIOS-e820: 00000000bdf19000 - 00000000bdf1f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bdf1f000 - 00000000bdf64000 (usable)
[ 0.000000] BIOS-e820: 00000000bdf64000 - 00000000bdf9f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bdf9f000 - 00000000be000000 (ACPI data)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[ 0.000000] Warning only 4GB will be used.
[ 0.000000] Use a HIGHMEM64G enabled kernel.
[ 0.000000] 3200MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00f75c0] 000f75c0
[ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 1048576
[ 0.000000] On node 0 totalpages: 1048576
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 6400 pages used for memmap
[ 0.000000] HighMem zone: 812800 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7530, 0024 (r2 LENOVO)
[ 0.000000] ACPI: XSDT BDFF8423, 0074 (r1 LENOVO CB-01 0 LTP 0)
[ 0.000000] ACPI: FACP BDFE8000, 00F4 (r3 LENOVO CB-01 1 ALAN 1)
[ 0.000000] ACPI: DSDT BDFE9000, 672B (r2 LENOVO CB-01 1 INTL 20050624)
[ 0.000000] ACPI: FACS BDF9EFC0, 0040
[ 0.000000] ACPI: HPET BDFFED52, 0038 (r1 LENOVO CB-01 1 LOHR 5A)
[ 0.000000] ACPI: MCFG BDFFED8A, 003C (r1 LENOVO CB-01 1 LOHR 5A)
[ 0.000000] ACPI: SLIC BDFFEDC6, 0176 (r1 LENOVO CB-01 1 TBD 1)
[ 0.000000] ACPI: DBGP BDFFEF3C, 0034 (r1 LENOVO CB-01 1 LOHR 0)
[ 0.000000] ACPI: APIC BDFFEF70, 0068 (r1 PTLTD APIC 0 LTP 0)
[ 0.000000] ACPI: BOOT BDFFEFD8, 0028 (r1 PTLTD $SBFTBL$ 0 LTP 1)
[ 0.000000] ACPI: SSDT BDFE7000, 0655 (r1 PmRef CpuPm 3000 INTL 20050624)
[ 0.000000] ACPI: SSDT BDFE6000, 0259 (r1 PmRef Cpu0Tst 3000 INTL 20050624)
[ 0.000000] ACPI: SSDT BDFE5000, 020F (r1 PmRef ApTst 3000 INTL 20050624)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: be000000:42000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
[ 0.000000] Kernel command line: root=/dev/sda1 ro splash vga=791 quiet quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 2094.857 MHz processor.
[ 0.004000] Console: colour dummy device 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 3063064k/4194304k available (1770k kernel code, 45524k reserved, 750k data, 244k init, 2192368k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02baaa1 - 0xc0376620 ( 750 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02baaa1 (1770 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.083861] Calibrating delay using timer specific routine.. 4193.86 BogoMIPS (lpj=8387727)
[ 0.083890] Security Framework initialized
[ 0.083895] SELinux: Disabled at boot.
[ 0.083898] Capability LSM initialized
[ 0.083909] Mount-cache hash table entries: 512
[ 0.084005] Initializing cgroup subsys ns
[ 0.084005] Initializing cgroup subsys cpuacct
[ 0.084005] Initializing cgroup subsys devices
[ 0.084005] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084005] CPU: L2 cache: 2048K
[ 0.084005] CPU: Physical Processor ID: 0
[ 0.084005] CPU: Processor Core ID: 0
[ 0.084005] Intel machine check architecture supported.
[ 0.084005] Intel machine check reporting enabled on CPU#0.
[ 0.084005] using mwait in idle threads.
[ 0.084005] Checking 'hlt' instruction... OK.
[ 0.100006] ACPI: Core revision 20080321
[ 0.112007] ENABLING IO-APIC IRQs
[ 0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.151665] CPU0: Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz stepping 0a
[ 0.152009] Booting processor 1/1 ip 6000
[ 0.160010] Initializing CPU#1
[ 0.160010] Calibrating delay using timer specific routine.. 4189.46 BogoMIPS (lpj=8378922)
[ 0.160010] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160010] CPU: L2 cache: 2048K
[ 0.160010] CPU: Physical Processor ID: 0
[ 0.160010] CPU: Processor Core ID: 1
[ 0.160010] Intel machine check architecture supported.
[ 0.160010] Intel machine check reporting enabled on CPU#1.
[ 0.240015] CPU1: Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz stepping 0a
[ 0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.244015] Brought up 2 CPUs
[ 0.244015] Total of 2 processors activated (8383.32 BogoMIPS).
[ 0.244015] CPU0 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 0 1
[ 0.244015] CPU1 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 1 0
[ 0.244015] net_namespace: 660 bytes
[ 0.244015] Booting paravirtualized kernel on bare hardware
[ 0.244015] NET: Registered protocol family 16
[ 0.244015] ACPI: bus type pci registered
[ 0.244015] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.244015] PCI: Not using MMCONFIG.
[ 0.244015] PCI: PCI BIOS revision 3.00 entry at 0xfde21, last bus=8
[ 0.244015] PCI: Using configuration type 1 for base access
[ 0.244015] Setting up standard PCI resources
[ 0.248015] ACPI: EC: Look up EC in DSDT
[ 0.250890] ACPI: BIOS _OSI(Linux) query ignored
[ 0.250892] ACPI: DMI System Vendor: LENOVO
[ 0.250894] ACPI: DMI Product Name: 20023
[ 0.250895] ACPI: DMI Product Version: Lenovo G550
[ 0.250897] ACPI: DMI Board Name: NITU1
[ 0.250898] ACPI: DMI BIOS Vendor: LENOVO
[ 0.250899] ACPI: DMI BIOS Date: 08/05/2009
[ 0.250901] ACPI: Please send DMI info above to linux-acpi@vger.kernel.org
[ 0.250903] ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
[ 0.256016] ACPI: Interpreter enabled
[ 0.256018] ACPI: (supports S0 S3 S4 S5)
[ 0.256464] ACPI: Using IOAPIC for interrupt routing
[ 0.256464] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.293026] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.293028] PCI: Using MMCONFIG for extended config space
[ 0.296467] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.356471] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.356471] ACPI: EC: driver started in interrupt mode
[ 0.356471] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.361483] PCI: Transparent bridge - 0000:00:1e.0
[ 0.361539] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.361743] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.361883] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.361993] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.362100] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.362210] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.362320] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.370928] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 0.370928] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.370928] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[ 0.370928] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.370928] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[ 0.370928] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.370928] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.370928] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 *4 5 6 7 11 12 14 15)
[ 0.370928] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.370928] pnp: PnP ACPI init
[ 0.370928] ACPI: bus type pnp registered
[ 0.391554] pnp: PnP ACPI: found 10 devices
[ 0.391554] ACPI: ACPI bus type pnp unregistered
[ 0.391554] PnPBIOS: Disabled by ACPI PNP
[ 0.391554] PCI: Using ACPI for IRQ routing
[ 0.398447] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.398452] hpet0: 4 64-bit timers, 14318180 Hz
[ 0.402384] ACPI: RTC can wake from S4
[ 0.409324] system 00:03: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.409330] system 00:05: ioport range 0x680-0x69f has been reserved
[ 0.409333] system 00:05: ioport range 0x480-0x48f has been reserved
[ 0.409335] system 00:05: ioport range 0xffff-0xffff has been reserved
[ 0.409337] system 00:05: ioport range 0xffff-0xffff has been reserved
[ 0.409340] system 00:05: ioport range 0x400-0x47f has been reserved
[ 0.409342] system 00:05: ioport range 0x1180-0x11ff has been reserved
[ 0.409344] system 00:05: ioport range 0x164e-0x164f has been reserved
[ 0.409346] system 00:05: ioport range 0xfe00-0xfe00 has been reserved
[ 0.409353] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.409356] system 00:09: iomem range 0xfed10000-0xfed13fff has been reserved
[ 0.409358] system 00:09: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.409360] system 00:09: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.409363] system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.409365] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.409368] system 00:09: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.438441] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0
[ 0.438441] PCI: Bridge: 0000:00:01.0
[ 0.438441] IO window: 2000-2fff
[ 0.438441] MEM window: 0xf4000000-0xf6ffffff
[ 0.438441] PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
[ 0.438441] PCI: Bridge: 0000:00:1c.0
[ 0.438441] IO window: disabled.
[ 0.438441] MEM window: disabled.
[ 0.438441] PREFETCH window: disabled.
[ 0.438441] PCI: Bridge: 0000:00:1c.1
[ 0.438441] IO window: disabled.
[ 0.438441] MEM window: disabled.
[ 0.438441] PREFETCH window: disabled.
[ 0.438441] PCI: Bridge: 0000:00:1c.2
[ 0.438441] IO window: disabled.
[ 0.438441] MEM window: 0xf7100000-0xf71fffff
[ 0.438441] PREFETCH window: disabled.
[ 0.438441] PCI: Bridge: 0000:00:1c.3
[ 0.438441] IO window: 3000-3fff
[ 0.438441] MEM window: 0xf0000000-0xf3ffffff
[ 0.438441] PREFETCH window: 0x00000000f8000000-0x00000000f9ffffff
[ 0.438441] PCI: Bridge: 0000:00:1c.5
[ 0.438441] IO window: disabled.
[ 0.438441] MEM window: 0xf7000000-0xf70fffff
[ 0.438441] PREFETCH window: disabled.
[ 0.438441] PCI: Bridge: 0000:00:1e.0
[ 0.438441] IO window: disabled.
[ 0.438441] MEM window: disabled.
[ 0.438441] PREFETCH window: disabled.
[ 0.438441] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.438441] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.438441] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.438441] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.438441] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.438441] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.438441] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 0.438441] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.438441] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 0.438441] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.438441] ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.438442] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.438442] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.438442] NET: Registered protocol family 2
[ 0.451723] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.451913] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.452227] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.454092] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.454095] TCP reno registered
[ 0.461408] NET: Registered protocol family 1
[ 0.461496] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.515489] Switched to high resolution mode on CPU 0
[ 0.743593] it is
[ 1.043603] Freeing initrd memory: 8564k freed
[ 1.043604] Simple Boot Flag at 0x36 set to 0x1
[ 1.043972] audit: initializing netlink socket (disabled)
[ 1.043972] type=2000 audit(1258649924.028:1): initialized
[ 1.043972] highmem bounce pool size: 64 pages
[ 1.043972] Total HugeTLB memory allocated, 0
[ 1.043972] VFS: Disk quotas dquot_6.5.1
[ 1.043972] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.043972] msgmni has been set to 1719
[ 1.043972] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.043972] io scheduler noop registered
[ 1.043972] io scheduler anticipatory registered
[ 1.043972] io scheduler deadline registered
[ 1.043972] io scheduler cfq registered (default)
[ 1.043972] pci 0000:01:00.0: Boot video device
[ 1.043972] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 1.043972] assign_interrupt_mode Found MSI capability
[ 1.043972] Allocate Port Service[0000:00:01.0:pcie00]
[ 1.043972] Allocate Port Service[0000:00:01.0:pcie02]
[ 1.043972] Allocate Port Service[0000:00:01.0:pcie03]
[ 1.043972] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.043972] assign_interrupt_mode Found MSI capability
[ 1.043972] Allocate Port Service[0000:00:1c.0:pcie00]
[ 1.043972] Allocate Port Service[0000:00:1c.0:pcie02]
[ 1.043972] Allocate Port Service[0000:00:1c.0:pcie03]
[ 1.043972] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.043972] assign_interrupt_mode Found MSI capability
[ 1.043972] Allocate Port Service[0000:00:1c.1:pcie00]
[ 1.043972] Allocate Port Service[0000:00:1c.1:pcie02]
[ 1.043972] Allocate Port Service[0000:00:1c.1:pcie03]
[ 1.043972] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 1.043972] assign_interrupt_mode Found MSI capability
[ 1.043972] Allocate Port Service[0000:00:1c.2:pcie00]
[ 1.043972] Allocate Port Service[0000:00:1c.2:pcie02]
[ 1.043972] Allocate Port Service[0000:00:1c.2:pcie03]
[ 1.043972] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 1.043972] assign_interrupt_mode Found MSI capability
[ 1.043972] Allocate Port Service[0000:00:1c.3:pcie00]
[ 1.043972] Allocate Port Service[0000:00:1c.3:pcie02]
[ 1.043972] Allocate Port Service[0000:00:1c.3:pcie03]
[ 1.043972] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 1.043972] assign_interrupt_mode Found MSI capability
[ 1.043972] Allocate Port Service[0000:00:1c.5:pcie00]
[ 1.043972] Allocate Port Service[0000:00:1c.5:pcie02]
[ 1.043972] Allocate Port Service[0000:00:1c.5:pcie03]
[ 1.044254] vesafb: framebuffer at 0xf5000000, mapped to 0xf8880000, using 3072k, total 14336k
[ 1.044257] vesafb: mode is 1024x768x16, linelength=2048, pages=1
[ 1.044259] vesafb: protected mode interface info at c000:cd10
[ 1.044261] vesafb: pmi: set display start = c00ccd73, set palette = c00ccdce
[ 1.044263] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
[ 1.044272] vesafb: scrolling: redraw
[ 1.044274] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 1.068955] Console: switching to colour frame buffer device 128x48
[ 1.093581] fb0: VESA VGA frame buffer device
[ 1.095971] isapnp: Scanning for PnP cards...
[ 1.407973] isapnp: No Plug & Play device found
[ 1.407973] hpet_resources: 0xfed00000 is busy
[ 1.407973] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.407984] brd: module loaded
[ 1.407984] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.498503] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.498506] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.500659] mice: PS/2 mouse device common for all mice
[ 1.500659] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.500659] rtc0: alarms up to one month, y3k
[ 1.500659] cpuidle: using governor ladder
[ 1.500659] cpuidle: using governor menu
[ 1.500659] No iBFT detected.
[ 1.502037] TCP cubic registered
[ 1.502040] NET: Registered protocol family 17
[ 1.502047] Using IPI No-Shortcut mode
[ 1.504991] registered taskstats version 1
[ 1.504991] rtc_cmos 00:06: setting system clock to 2009-11-19 16:58:45 UTC (1258649925)
[ 1.504991] Freeing unused kernel memory: 244k freed
[ 1.585656] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.617532] ACPI: SSDT BDF1ACA0, 0223 (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 1.617956] ACPI: SSDT BDF19620, 0549 (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 1.618132] Monitor-Mwait will be used to enter C-1 state
[ 1.618132] Monitor-Mwait will be used to enter C-2 state
[ 1.618132] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 1.618132] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.618132] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.618132] ACPI: SSDT BDF1AA20, 01CF (r1 PmRef ApIst 3000 INTL 20050624)
[ 1.618132] ACPI: SSDT BDF1AF20, 008D (r1 PmRef ApCst 3000 INTL 20050624)
[ 1.629864] Marking TSC unstable due to: TSC halts in idle.
[ 1.631869] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 1.631869] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.631869] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.633591] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.639017] ACPI: Thermal Zone [TZ00] (45 C)
[ 1.847501] usbcore: registered new interface driver usbfs
[ 1.847501] usbcore: registered new interface driver hub
[ 1.859500] usbcore: registered new device driver usb
[ 1.867428] USB Universal Host Controller Interface driver v3.0
[ 1.867465] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.867474] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.867478] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.867575] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.867612] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 1.867680] usb usb1: configuration #1 chosen from 1 choice
[ 1.867704] hub 1-0:1.0: USB hub found
[ 1.867710] hub 1-0:1.0: 2 ports detected
[ 1.914439] No dock devices found.
[ 1.930411] SCSI subsystem initialized
[ 1.942998] libata version 3.00 loaded.
[ 1.970540] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.970544] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.970546] usb usb1: Product: UHCI Host Controller
[ 1.970548] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.970549] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.972610] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 1.972619] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 1.972623] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.972642] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.972674] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 1.972737] usb usb2: configuration #1 chosen from 1 choice
[ 1.972760] hub 2-0:1.0: USB hub found
[ 1.972765] hub 2-0:1.0: 2 ports detected
[ 2.074384] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.074390] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.074393] usb usb2: Product: UHCI Host Controller
[ 2.074396] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.074399] usb usb2: SerialNumber: 0000:00:1a.1
[ 2.077491] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 20 (level, low) -> IRQ 20
[ 2.077491] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 2.077491] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 2.077491] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 2.077491] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001840
[ 2.077491] usb usb3: configuration #1 chosen from 1 choice
[ 2.077491] hub 3-0:1.0: USB hub found
[ 2.077491] hub 3-0:1.0: 2 ports detected
[ 2.180493] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.180498] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.180502] usb usb3: Product: UHCI Host Controller
[ 2.180505] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.180508] usb usb3: SerialNumber: 0000:00:1a.2
[ 2.180736] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 20 (level, low) -> IRQ 20
[ 2.180736] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 2.180736] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.180736] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 4
[ 2.181884] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.181890] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 2.181894] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf7405800
[ 2.212922] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 2.225669] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.225749] usb usb4: configuration #1 chosen from 1 choice
[ 2.225789] hub 4-0:1.0: USB hub found
[ 2.225799] hub 4-0:1.0: 6 ports detected
[ 2.280712] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 2.329960] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.329960] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.329960] usb usb4: Product: EHCI Host Controller
[ 2.329960] usb usb4: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 2.329960] usb usb4: SerialNumber: 0000:00:1a.7
[ 2.329960] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.329960] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.329960] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.329960] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.329960] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[ 2.329960] usb usb5: configuration #1 chosen from 1 choice
[ 2.329960] hub 5-0:1.0: USB hub found
[ 2.329960] hub 5-0:1.0: 2 ports detected
[ 2.433386] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.433391] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.433394] usb usb5: Product: UHCI Host Controller
[ 2.433397] usb usb5: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.433400] usb usb5: SerialNumber: 0000:00:1d.0
[ 2.434763] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.434763] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.434763] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.434763] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.434763] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[ 2.434763] usb usb6: configuration #1 chosen from 1 choice
[ 2.434763] hub 6-0:1.0: USB hub found
[ 2.434763] hub 6-0:1.0: 2 ports detected
[ 2.528718] Clocksource tsc unstable (delta = -472874236 ns)
[ 2.537669] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.537674] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.537678] usb usb6: Product: UHCI Host Controller
[ 2.537681] usb usb6: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.537684] usb usb6: SerialNumber: 0000:00:1d.1
[ 2.538750] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.538750] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.538750] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.538750] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.538750] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[ 2.538750] usb usb7: configuration #1 chosen from 1 choice
[ 2.538750] hub 7-0:1.0: USB hub found
[ 2.538750] hub 7-0:1.0: 2 ports detected
[ 2.641742] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.641746] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.641750] usb usb7: Product: UHCI Host Controller
[ 2.641753] usb usb7: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.641756] usb usb7: SerialNumber: 0000:00:1d.2
[ 2.641876] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.641876] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.641876] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.641876] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 2.642762] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.642768] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.642772] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7405c00
[ 2.658767] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.658844] usb usb8: configuration #1 chosen from 1 choice
[ 2.658844] hub 8-0:1.0: USB hub found
[ 2.658844] hub 8-0:1.0: 6 ports detected
[ 2.762114] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.762118] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.762122] usb usb8: Product: EHCI Host Controller
[ 2.762125] usb usb8: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 2.762128] usb usb8: SerialNumber: 0000:00:1d.7
[ 2.763184] ahci 0000:00:1f.2: version 3.0
[ 2.763184] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 3.159937] usb 1-1: new full speed USB device using uhci_hcd and address 3
[ 3.331873] usb 1-1: configuration #1 chosen from 1 choice
[ 3.335074] usb 1-1: New USB device found, idVendor=0a5c, idProduct=2150
[ 3.335077] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.335079] usb 1-1: Product: BCM2046 Bluetooth Device
[ 3.335080] usb 1-1: Manufacturer: Broadcom Corp
[ 3.335082] usb 1-1: SerialNumber: 00265E9E6742
[ 3.759383] usb 8-3: new high speed USB device using ehci_hcd and address 3
[ 3.767726] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x13 impl SATA mode
[ 3.767732] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part
[ 3.767739] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 3.769880] scsi0 : ahci
[ 3.769880] scsi1 : ahci
[ 3.769880] scsi2 : ahci
[ 3.769880] scsi3 : ahci
[ 3.769880] scsi4 : ahci
[ 3.769880] ata1: SATA max UDMA/133 abar m2048@0xf7405000 port 0xf7405100 irq 217
[ 3.769880] ata2: SATA max UDMA/133 abar m2048@0xf7405000 port 0xf7405180 irq 217
[ 3.769880] ata3: DUMMY
[ 3.769880] ata4: DUMMY
[ 3.769880] ata5: SATA max UDMA/133 abar m2048@0xf7405000 port 0xf7405300 irq 217
[ 4.005378] usb 8-3: configuration #1 chosen from 1 choice
[ 4.025703] usb 8-3: New USB device found, idVendor=5986, idProduct=0145
[ 4.025703] usb 8-3: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[ 4.025703] usb 8-3: Product: Lenovo EasyCamera
[ 4.025703] usb 8-3: Manufacturer: Bison Electronics Inc.
[ 4.090306] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.091757] ata1.00: ATA-8: Hitachi HTS543232L9A300, FB4OC4DC, max UDMA/133
[ 4.091757] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.092279] ata1.00: configured for UDMA/133
[ 4.263061] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 4.426423] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.430195] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T50N, RV06, max UDMA/133
[ 4.434654] usb 5-1: configuration #1 chosen from 1 choice
[ 4.434954] ata2.00: configured for UDMA/133
[ 4.437308] usb 5-1: New USB device found, idVendor=09da, idProduct=000a
[ 4.437308] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.437308] usb 5-1: Product: PS/2+USB Mouse
[ 4.437308] usb 5-1: Manufacturer: A4Tech
[ 4.453191] usbcore: registered new interface driver hiddev
[ 4.462603] input: A4Tech PS/2+USB Mouse as /class/input/input1
[ 4.462603] input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:1d.0-1
[ 4.462603] usbcore: registered new interface driver usbhid
[ 4.462603] usbhid: v2.6:USB HID core driver
[ 4.768297] ata5: SATA link down (SStatus 0 SControl 300)
[ 4.784396] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54323 FB4O PQ: 0 ANSI: 5
[ 4.786438] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T50N RV06 PQ: 0 ANSI: 5
[ 4.788715] tg3.c:v3.92.1 (June 9, 2008)
[ 4.788715] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 4.788715] PCI: Setting latency timer of device 0000:07:00.0 to 64
[ 5.124176] eth0: Tigon3 [partno(BCM95906) rev c002 PHY(5906)] (PCI Express) 10/100Base-TX Ethernet 00:26:22:05:14:a4
[ 5.124179] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[0]
[ 5.124182] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 5.135747] Driver 'sd' needs updating - please use bus_type methods
[ 5.135748] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 5.135748] sd 0:0:0:0: [sda] Write Protect is off
[ 5.135748] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.135748] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.135748] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 5.135748] sd 0:0:0:0: [sda] Write Protect is off
[ 5.135748] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.135748] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.135748] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 5.155537] sda1 sda2 sda3 sda4
[ 5.186041] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.405328] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.405328] Uniform CD-ROM driver Revision: 3.20
[ 5.405328] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 5.414196] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.414196] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 6.304314] PM: Starting manual resume from disk
[ 7.402089] kjournald starting. Commit interval 5 seconds
[ 7.402089] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.432339] udevd version 125 started
[ 10.005020] Linux agpgart interface v0.103
[ 10.036049] input: Power Button (FF) as /class/input/input2
[ 10.091800] ACPI: Power Button (FF) [PWRF]
[ 10.091853] input: Lid Switch as /class/input/input3
[ 10.124700] ACPI: Lid Switch [LID0]
[ 10.124747] input: Power Button (CM) as /class/input/input4
[ 10.189132] ACPI: Power Button (CM) [PWRB]
[ 10.189181] input: Sleep Button (CM) as /class/input/input5
[ 10.251881] ACPI: Sleep Button (CM) [SLPB]
[ 10.257770] ACPI: device:04 is registered as cooling_device2
[ 10.257969] input: Video Bus as /class/input/input6
[ 10.315502] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 10.319349] ACPI: device:08 is registered as cooling_device3
[ 10.337772] ACPI: device:09 is registered as cooling_device4
[ 10.341772] ACPI: device:0a is registered as cooling_device5
[ 10.352503] ACPI: device:0b is registered as cooling_device6
[ 10.360501] ACPI: device:0c is registered as cooling_device7
[ 10.360501] input: Video Bus as /class/input/input7
[ 10.422447] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 10.422407] ACPI: AC Adapter [ACAD] (on-line)
[ 10.474338] Bluetooth: Core ver 2.11
[ 10.482864] NET: Registered protocol family 31
[ 10.482864] Bluetooth: HCI device and connection manager initialized
[ 10.482864] Bluetooth: HCI socket layer initialized
[ 10.494866] Bluetooth: HCI USB driver ver 2.9
[ 10.495214] usbcore: registered new interface driver hci_usb
[ 10.564694] ACPI: Battery Slot [BAT1] (battery present)
[ 10.825739] input: PC Speaker as /class/input/input8
[ 10.863697] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
[ 10.864692] Linux video capture interface: v2.00
[ 10.892810] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (5986:0145)
[ 10.897544] input: Lenovo EasyCamera as /class/input/input9
[ 10.919877] usbcore: registered new interface driver uvcvideo
[ 10.919881] USB Video Class driver (v0.1.0)
[ 11.043589] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 11.043614] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 12.033687] input: PS/2 Mouse as /class/input/input10
[ 12.093138] input: AlpsPS/2 ALPS GlidePoint as /class/input/input11
[ 12.634715] Adding 7783484k swap on /dev/sda4. Priority:-1 extents:1 across:7783484k
[ 13.145815] EXT3 FS on sda1, internal journal
[ 13.499256] loop: module loaded
[ 114.146020] kjournald starting. Commit interval 5 seconds
[ 114.146234] EXT3 FS on sda2, internal journal
[ 114.146234] EXT3-fs: mounted filesystem with ordered data mode.
[ 114.203842] kjournald starting. Commit interval 5 seconds
[ 114.204509] EXT3 FS on sda3, internal journal
[ 114.204515] EXT3-fs: mounted filesystem with ordered data mode.
[ 117.133267] ACPI: WMI: Mapper loaded
[ 117.917721] NET: Registered protocol family 10
[ 117.918064] lo: Disabled Privacy Extensions
[ 132.819773] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 133.227976] nvidia: module license 'NVIDIA' taints kernel.
[ 133.480535] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 133.480547] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 133.480675] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.09 Wed Jun 4 23:43:17 PDT 2008
[ 134.473641] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 134.473641] tg3: eth0: Flow control is on for TX and on for RX.
[ 135.369643] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 135.950973] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 137.521977] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 137.521977] tg3: eth0: Flow control is on for TX and on for RX.
[ 137.521977] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 147.832106] eth0: no IPv6 routers present
[ 161.206705] CPU0 attaching NULL sched-domain.
[ 161.206711] CPU1 attaching NULL sched-domain.
[ 161.214673] CPU0 attaching sched-domain:
[ 161.214673] domain 0: span 0-1
[ 161.214673] groups: 0 1
[ 161.214673] CPU1 attaching sched-domain:
[ 161.214673] domain 0: span 0-1
[ 161.214673] groups: 1 0 lenny kernel 2.6.26-2-686 Po zainstalowaniu pakietu firmware-iwlwifi i restarcie nic się nie zmieniło. Nadal nie wykrywa karty.

sidjestgit - 19-11-2009 21:45
Zainstaluj kernel z backortow.
dodaj do /etc/apt/sources.list taki wpis
deb http://www.backports.org/debian lenny-backports main contrib non-free nastepnie
su
apt-get update
apt-cache search linux-image apt-get install nazwa_kernela_jaki_wybrales np:
apt-get install linux-image-2.6.30-bpo.2-686 odinstaluj stary pakiet firmware-iwlwifi
apt-get remove --purge firmware-iwlwifi Restart systemu - uruchom system na nowym kernelu.

sciagnij i zainstaluj nowsza wersje firmware-iwlwifi
wget http://www.backports.org/debian/pool...po50+1_all.deb dpkg -i firmware-iwlwifi_0.17~bpo50+1_all.deb ifconfig wlan0 up uruchom wicd - i polacz sie z siecia.

szcz00ri - 19-11-2009 23:06
Dobra sprawa wlan rozwiązana, ale po instalacji nowego jądra X-y mi nie wstały.

Doinstalowałem headers i podczas instalacji wyskoczyła mi informacja No precompiled kernel interface was found to match your kernel; this means that the installer will need to compilke a new kernel interface. Następne okienko:
Depending on where and how the kernel sources (or the kernel headers) were installed, you may need to specify their location with the SYSSRC environment variable or the equivalent nvidia-installer command line option. Na sterowniku Vesa działa.

Jakieś propozycje?

fnmirk - 20-11-2009 06:59

Na sterowniku Vesa działa. Potrzebna instalacja sterowników karty graficzne.

szcz00ri - 20-11-2009 07:05
Też tak myślę, ale z jakiegoś powodu nie chcą się zainstalować. Na starym kernelu korzystając z tego poradnika HOWTO wszystko poszło bez problemów.

Sterownik
NVIDIA-Linux-x86-173.14.09-pkg1.run Błędy jakie się pokazują podczas instalacji napisałem w poście wyżej.

edit

Poradziłem sobie. Zainstalowałem najnowszy sterownik.

NVIDIA-Linux-x86-190.42-pkg1.run Dziękuję wszystkim za pomoc.

[ Dodano: |20 Lis 2009|, 2009 11:12 ]
Jeden problem zniknął to następny się pojawił.

Hibernacja przestała mi działać. Laptop się hibernuje, ale po wybudzeniu dochodzi do 100% i pojawia się czarny ekran.

Gdzieś na forum przeczytałem, że trzeba zakomentować "nvidia" w /etc/hibernate/blacklisted-modules . Nie pomogło.

kuba_astr - 14-12-2009 19:01
Przepraszam, że tak z buta bez przywitania się wtrącę w wątek ale nigdzie (absolutnie nigdzie) w sieci nie ma informacji na temat konfiguracji i 5100 pod jądrem 2.6.26.
Rozumiem, że najprostszym rozwiązaniem jest instalacja nowego jajca ale cóż... Nie wchodzi to w grę. Mam laptopa Lenovo t400 i przy jądrach wyższych niż 2.6.26 wywala mi całkowicie ACPI (nie działa BT, i skróty klawiszowe FN+...)
Jest to jakaś masakra!
Mogę mieć wifi i pół-system, lub stabilny system i brak wifi.

Może macie jakieś sugestie, najlepiej jak dodać sterowniki do 5100 do jądra 2.6.26.
debian:/home/kuba/Desktop# modprobe iwlagn
FATAL: Module iwlagn not found.
debian:/home/kuba/Desktop# modprobe iwlwifi
FATAL: Module iwlwifi not found.
debian:/home/kuba/Desktop# Pozdrawiam
Kuba

iria - 14-12-2009 19:51
Spróbowałeś, po prostu zainstalować paczkę z firmware do kart Intela, np. ze Squeeze?

kuba_astr - 14-12-2009 20:39
Iria: nie za bardzo, próbowałem coś wykombinowac z dograniem firmware'u z intellinux.... Ale to chyba na nic...

iria - 14-12-2009 20:41
Pytam, czy robiłeś to, a nie interesuje mnie co innego. Czy propozycja mojego rozwiązania działa?

kuba_astr - 14-12-2009 20:49
Ok, z miłą chęcią spróbuję ale nie wiem od czego zacząć :-(
Dasz mi jakiś krótki guide?

iria - 14-12-2009 20:51
http://packages.debian.org/squeeze/firmware-iwlwifi

ÂŚciągasz paczkę i instalujesz ją za pomocą dpkg. Później reset komputera. Zobaczymy czy nowszy firmware zostanie przyjęty przez jajko.

kuba_astr - 14-12-2009 20:54
Ok już działam dzięki, dam znać po restarcie.

K

[ Dodano: |14 Gru 2009|, 2009 20:58 ]
Ok, po restarcie i zainstalowaniu ver 0.18:

debian:/home/kuba# iwconfig
lo no wireless extensions.

eth0 no wireless extensions. debian:/home/kuba# lspci |grep rel
03:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection nie widać wciąż karty.. ;(

iria - 14-12-2009 21:07
Wynik

lsmod poproszę.

Strona 1 z 2 • Wyszukano 40 postów • 1, 2