Nagły zanik dźwięku

rlk120 - 10-06-2009 18:50
Wiem, że mam dużo problemów z tym dźwiękiem, ale właśnie nagle mi się popsuł.

Sprawdzałem wszystko i wszędzie jest dobrze, ustawione na EMU 0404, ale dźwięku nie ma.

Wszystkie miksery poustawiane na maksimum, a dźwięku nie ma.

Przeinstalowałbym alsę, ale nie umiem.

ilin - 11-06-2009 08:12
cat /proc/asound/modules Pokaże czy sterownik od dźwięku siedzi w jądrze.

Podejrewam ze sobie sam dźwięk wyłączyleś :)

alsamixer Są tam jeszcze przełączniki M OO Przełączasz klawiszem m pobaw się tym mając puszczony w drugim terminalu
speaker-test Jest jeszcze jedna mozliwość.

Karty dzwiękowe się miejscami zamienily.(pamiętam ze masz dwie)

cat /proc/asound/cards poinformuje o tym.

rlk120 - 11-06-2009 08:33
cat /proc/asound/modules
0 snd_emu10k1
1 snd_via82xx cat /proc/asound/cards
0 [EMU0404 ]: Audigy2 - E-mu 0404b [4002]
E-mu 0404b [4002] (rev.0, serial:0x40021102) at 0xa400, irq 17
1 [V8237 ]: VIA8237 - VIA 8237
VIA 8237 with ALC850 at 0x1000, irq 22
Na moje oko wszystko jest ok.

Zmiana w alsamixer też nic nie dała.

ilin - 11-06-2009 08:44
Zobacz do dmesg czy jest coś na temat firmware.

rlk120 - 11-06-2009 10:27
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-12) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Mon Dec 15 18:15:07 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000006ffb0000 (usable)
[ 0.000000] BIOS-e820: 000000006ffb0000 - 000000006ffc0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000006ffc0000 - 000000006fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000006fff0000 - 0000000070000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 895MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 458672) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 458672
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 458672
[ 0.000000] On node 0 totalpages: 458672
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1792 pages used for memmap
[ 0.000000] HighMem zone: 227504 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FA810, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 6FFB0000, 0030 (r1 A M I OEMRSDT 5000729 MSFT 97)
[ 0.000000] ACPI: FACP 6FFB0200, 0081 (r1 A M I OEMFACP 5000729 MSFT 97)
[ 0.000000] ACPI: DSDT 6FFB03F0, 391B (r1 A0277 A0277001 1 MSFT 100000D)
[ 0.000000] ACPI: FACS 6FFC0000, 0040
[ 0.000000] ACPI: APIC 6FFB0390, 0052 (r1 A M I OEMAPIC 5000729 MSFT 97)
[ 0.000000] ACPI: OEMB 6FFC0040, 003F (r1 A M I OEMBIOS 5000729 MSFT 97)
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 70000000:8f780000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 455088
[ 0.000000] Kernel command line: root=/dev/sda7 ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2403.192 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 1808832k/1834688k available (1769k kernel code, 24540k reserved, 752k data, 244k init, 917184k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba46b - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba46b (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084111] Calibrating delay using timer specific routine.. 4812.12 BogoMIPS (lpj=9624243)
[ 0.084145] Security Framework initialized
[ 0.084152] SELinux: Disabled at boot.
[ 0.084155] Capability LSM initialized
[ 0.084169] Mount-cache hash table entries: 512
[ 0.084311] Initializing cgroup subsys ns
[ 0.084315] Initializing cgroup subsys cpuacct
[ 0.084317] Initializing cgroup subsys devices
[ 0.084335] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.084337] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.084341] Intel machine check architecture supported.
[ 0.084343] Intel machine check reporting enabled on CPU#0.
[ 0.084357] Checking 'hlt' instruction... OK.
[ 0.100321] SMP alternatives: switching to UP code
[ 0.105466] ACPI: Core revision 20080321
[ 0.110610] ENABLING IO-APIC IRQs
[ 0.110939] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
[ 0.150665] CPU0: AMD Athlon(tm) 64 Processor 4000+ stepping 02
[ 0.152009] Brought up 1 CPUs
[ 0.152009] Total of 1 processors activated (4812.12 BogoMIPS).
[ 0.152009] CPU0 attaching sched-domain:
[ 0.152009] domain 0: span 0
[ 0.152009] groups: 0
[ 0.152009] net_namespace: 660 bytes
[ 0.152009] Booting paravirtualized kernel on bare hardware
[ 0.152009] NET: Registered protocol family 16
[ 0.152009] ACPI: bus type pci registered
[ 0.152009] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[ 0.152009] PCI: Using configuration type 1 for base access
[ 0.152009] Setting up standard PCI resources
[ 0.156009] ACPI: EC: Look up EC in DSDT
[ 0.160010] ACPI: Interpreter enabled
[ 0.160010] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.160010] ACPI: Using IOAPIC for interrupt routing
[ 0.164482] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.165208] pci 0000:00:11.0: Enabled onboard AC97/MC97 devices
[ 0.165462] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.172265] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 0.172354] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
[ 0.172443] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 0.172531] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.172619] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.172707] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.172795] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.172883] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.172987] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - AD, should be A0 [20080321]
[ 0.172993] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.173012] pnp: PnP ACPI init
[ 0.173018] ACPI: bus type pnp registered
[ 0.176226] pnp: PnP ACPI: found 14 devices
[ 0.176228] ACPI: ACPI bus type pnp unregistered
[ 0.176231] PnPBIOS: Disabled by ACPI PNP
[ 0.176391] PCI: Using ACPI for IRQ routing
[ 0.176544] ACPI: RTC can wake from S4
[ 0.176562] system 00:09: ioport range 0x680-0x6ff has been reserved
[ 0.176565] system 00:09: ioport range 0x290-0x297 has been reserved
[ 0.176571] system 00:0a: ioport range 0x3e1-0x3e7 has been reserved
[ 0.176573] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[ 0.176576] system 00:0a: ioport range 0x800-0x87f has been reserved
[ 0.176578] system 00:0a: ioport range 0x400-0x41f has been reserved
[ 0.176584] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.176587] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.176589] system 00:0b: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.176595] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 0.176598] system 00:0d: iomem range 0xc0000-0xdffff could not be reserved
[ 0.176600] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 0.176603] system 00:0d: iomem range 0x100000-0x6ffeffff could not be reserved
[ 0.206869] PCI: Bridge: 0000:00:01.0
[ 0.206871] IO window: e000-efff
[ 0.206875] MEM window: 0xfbd00000-0xfbffffff
[ 0.206878] PREFETCH window: 0x00000000d0000000-0x00000000faffffff
[ 0.206892] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.206913] NET: Registered protocol family 2
[ 0.206985] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.207280] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.208035] Switched to high resolution mode on CPU 0
[ 0.208409] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.209012] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.209015] TCP reno registered
[ 0.209137] NET: Registered protocol family 1
[ 0.209235] checking if image is initramfs... it is
[ 0.603006] Freeing initrd memory: 6040k freed
[ 0.603608] audit: initializing netlink socket (disabled)
[ 0.603620] type=2000 audit(1244715899.600:1): initialized
[ 0.603775] highmem bounce pool size: 64 pages
[ 0.603779] Total HugeTLB memory allocated, 0
[ 0.603861] VFS: Disk quotas dquot_6.5.1
[ 0.603891] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.603928] msgmni has been set to 1755
[ 0.604045] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.604048] io scheduler noop registered
[ 0.604050] io scheduler anticipatory registered
[ 0.604052] io scheduler deadline registered
[ 0.604065] io scheduler cfq registered (default)
[ 0.604078] PCI: VIA PCI bridge detected.Disabling DAC.
[ 0.604149] pci 0000:01:00.0: Boot video device
[ 0.604422] isapnp: Scanning for PnP cards...
[ 0.958329] isapnp: No Plug & Play device found
[ 0.960293] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 0.960390] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.960724] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.961836] brd: module loaded
[ 0.961905] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.962273] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.962277] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.962393] mice: PS/2 mouse device common for all mice
[ 0.962494] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.962522] rtc0: alarms up to one year, y3k
[ 0.962550] cpuidle: using governor ladder
[ 0.962552] cpuidle: using governor menu
[ 0.962555] No iBFT detected.
[ 0.962944] TCP cubic registered
[ 0.962947] NET: Registered protocol family 17
[ 0.962952] Using IPI No-Shortcut mode
[ 0.963039] registered taskstats version 1
[ 0.963190] rtc_cmos 00:02: setting system clock to 2009-06-11 10:25:00 UTC (1244715900)
[ 0.963421] Freeing unused kernel memory: 244k freed
[ 0.992550] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.039702] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.464170] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1.464181] PCI: Disallowing DAC for device 0000:00:0a.0
[ 1.464204] skge 1.13 addr 0xfba00000 irq 17 chip Yukon-Lite rev 9
[ 1.464473] skge eth0: addr 00:13:d4:4c:69:ae
[ 1.504430] No dock devices found.
[ 1.528050] SCSI subsystem initialized
[ 1.541906] libata version 3.00 loaded.
[ 1.552097] sata_via 0000:00:0f.0: version 2.3
[ 1.552117] ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
[ 1.552157] sata_via 0000:00:0f.0: routed to hard irq line 10
[ 1.552218] scsi0 : sata_via
[ 1.552286] scsi1 : sata_via
[ 1.552305] ata1: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb000 irq 20
[ 1.552307] ata2: SATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xb008 irq 20
[ 1.561120] usbcore: registered new interface driver usbfs
[ 1.561144] usbcore: registered new interface driver hub
[ 1.561173] usbcore: registered new device driver usb
[ 1.568236] USB Universal Host Controller Interface driver v3.0
[ 1.752111] Floppy drive(s): fd0 is 1.44M
[ 1.756019] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 1.771851] FDC 0 is a post-1991 82077
[ 1.960014] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.125180] ata2.00: ATA-8: WDC WD5000AAKS-22A7B0, 01.03B01, max UDMA/133
[ 2.125183] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.133155] ata2.00: configured for UDMA/133
[ 2.133243] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AAKS-2 01.0 PQ: 0 ANSI: 5
[ 2.133506] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 2.133517] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 2.133624] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 2.133656] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000c800
[ 2.133724] usb usb1: configuration #1 chosen from 1 choice
[ 2.133744] hub 1-0:1.0: USB hub found
[ 2.133750] hub 1-0:1.0: 2 ports detected
[ 2.236076] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.236079] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.236081] usb usb1: Product: UHCI Host Controller
[ 2.236083] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.236084] usb usb1: SerialNumber: 0000:00:10.0
[ 2.236119] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 2.236125] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 2.236142] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 2.236158] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d000
[ 2.236207] usb usb2: configuration #1 chosen from 1 choice
[ 2.236225] hub 2-0:1.0: USB hub found
[ 2.236230] hub 2-0:1.0: 2 ports detected
[ 2.340062] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.340064] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.340067] usb usb2: Product: UHCI Host Controller
[ 2.340068] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.340070] usb usb2: SerialNumber: 0000:00:10.1
[ 2.340279] ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
[ 2.340286] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 2.340303] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 2.340320] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d400
[ 2.340373] usb usb3: configuration #1 chosen from 1 choice
[ 2.340392] hub 3-0:1.0: USB hub found
[ 2.340398] hub 3-0:1.0: 2 ports detected
[ 2.354526] Driver 'sd' needs updating - please use bus_type methods
[ 2.354614] sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 2.354630] sd 1:0:0:0: [sda] Write Protect is off
[ 2.354632] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.354658] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.354705] sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 2.354718] sd 1:0:0:0: [sda] Write Protect is off
[ 2.354721] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.354745] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.354748] sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 >
[ 2.421344] sd 1:0:0:0: [sda] Attached SCSI disk
[ 2.444131] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.444134] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.444137] usb usb3: Product: UHCI Host Controller
[ 2.444139] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.444140] usb usb3: SerialNumber: 0000:00:10.2
[ 2.444189] ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
[ 2.444199] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 2.444217] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 2.444249] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d800
[ 2.444314] usb usb4: configuration #1 chosen from 1 choice
[ 2.444340] hub 4-0:1.0: USB hub found
[ 2.444346] hub 4-0:1.0: 2 ports detected
[ 2.476014] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 2.548097] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.548100] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.548103] usb usb4: Product: UHCI Host Controller
[ 2.548104] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.548106] usb usb4: SerialNumber: 0000:00:10.3
[ 2.548158] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
[ 2.548171] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 2.548188] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 2.548220] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfbc00000
[ 2.600016] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.600074] usb usb5: configuration #1 chosen from 1 choice
[ 2.600095] hub 5-0:1.0: USB hub found
[ 2.600102] hub 5-0:1.0: 8 ports detected
[ 2.704086] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.704089] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.704092] usb usb5: Product: EHCI Host Controller
[ 2.704093] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.704095] usb usb5: SerialNumber: 0000:00:10.4
[ 2.709062] Uniform Multi-Platform E-IDE driver
[ 2.709066] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.709493] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:0f.1
[ 2.709513] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
[ 2.709523] VP_IDE: not 100% native mode: will probe irqs later
[ 2.709536] VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[ 2.709545] ide0: BM-DMA at 0xfc00-0xfc07
[ 2.709552] ide1: BM-DMA at 0xfc08-0xfc0f
[ 2.709555] Probing IDE interface ide0...
[ 2.996013] usb 1-1: device not accepting address 2, error -71
[ 3.052034] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 3.276042] Probing IDE interface ide1...
[ 4.420101] hdd: HL-DT-ST DVDRAM GSA-H10N, ATAPI CD/DVD-ROM drive
[ 4.476029] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 4.476768] hdd: UDMA/33 mode selected
[ 4.477247] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.477288] ide1 at 0x170-0x177,0x376 on irq 15
[ 4.499073] hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 4.499079] Uniform CD-ROM driver Revision: 3.20
[ 4.566334] PM: Starting manual resume from disk
[ 4.588009] kjournald starting. Commit interval 5 seconds
[ 4.588009] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.608021] usb 1-1: new full speed USB device using uhci_hcd and address 4
[ 4.752006] usb 1-1: configuration #1 chosen from 1 choice
[ 4.822392] usb 1-1: New USB device found, idVendor=1110, idProduct=9031
[ 4.822395] usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=3
[ 4.822397] usb 1-1: Product: ADSL-USB Modem
[ 4.822399] usb 1-1: SerialNumber: 00604CEBC9AC
[ 5.709878] udev: starting version 141
[ 5.709878] udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
[ 6.193561] Linux agpgart interface v0.103
[ 6.202612] agpgart: Detected AGP bridge 0
[ 6.203730] agpgart: AGP aperture is 32M @ 0xce000000
[ 6.403741] input: Power Button (FF) as /class/input/input1
[ 6.428140] ACPI: Power Button (FF) [PWRF]
[ 6.428215] input: Power Button (CM) as /class/input/input2
[ 6.460083] ACPI: Power Button (CM) [PWRB]
[ 6.460140] input: Sleep Button (CM) as /class/input/input3
[ 6.488076] ACPI: Sleep Button (CM) [SLPB]
[ 6.654772] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 6.659756] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.725447] NET: Registered protocol family 8
[ 6.725451] NET: Registered protocol family 20
[ 6.801477] [ueagle-atm] driver ueagle 1.4 loaded
[ 6.801495] usb 1-1: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X9031) Rev (0X200B): Eagle III
[ 6.898695] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 6.898747] emu1010: Special config.
[ 6.898859] emu1010: EMU_HANA_ID=0x3f
[ 6.898861] emu1010: filename emu/emu0404.fw testing
[ 6.898863] firmware: requesting emu/emu0404.fw
[ 6.912023] usb 1-1: reset full speed USB device using uhci_hcd and address 4
[ 7.032623] input: PC Speaker as /class/input/input4
[ 7.123931] usb 1-1: [ueagle-atm] using iso mode
[ 7.124093] usb 1-1: [ueagle-atm] (re)booting started
[ 7.125895] usbcore: registered new interface driver ueagle-atm
[ 7.256009] firmware size=0xd67c
[ 8.271855] emu1010: Hana Firmware loaded
[ 8.271900] Hana ver:1.1
[ 8.271955] emu1010: Card options=0x1
[ 8.271978] emu1010: Card options=0x1
[ 8.276006] emu1010: Card options3=0x1
[ 8.292422] Audigy2 value: Special config.
[ 8.292617] EMU outputs on
[ 8.292619] EMU2 inputs on
[ 8.298763] VIA 82xx Audio 0000:00:11.5: enabling device (0000 -> 0001)
[ 8.298772] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
[ 8.298915] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 8.364008] input: ImPS/2 Generic Wheel Mouse as /class/input/input5
[ 8.398899] parport_pc 00:08: reported by Plug and Play ACPI
[ 8.398937] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 8.812372] VIA 82xx Modem 0000:00:11.6: enabling device (0000 -> 0001)
[ 8.812378] ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 22
[ 9.384018] firmware: requesting ueagle-atm/DSPep.bin
[ 9.564015] PCI: Setting latency timer of device 0000:00:11.6 to 64
[ 9.600006] usb 1-1: [ueagle-atm] ATU-R firmware version : 44e2ea17
[ 9.600006] firmware: requesting ueagle-atm/CMVep.bin.v2
[ 9.665607] usb 1-1: [Ueagle-atm] requesting firmware ueagle-atm/CMVep.bin.v2 failed, try to get older cmvs
[ 9.665607] firmware: requesting ueagle-atm/CMVep.bin
[ 9.690823] usb 1-1: [Ueagle-atm] use deprecated cmvs version, please update your firmware
[ 9.712005] usb 1-1: [ueagle-atm] modem started, waiting synchronization...
[ 10.068206] ACPI: PCI interrupt for device 0000:00:11.6 disabled
[ 10.068215] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
[ 10.549849] Adding 1574328k swap on /dev/sda10. Priority:-1 extents:1 across:1574328k
[ 10.939335] EXT3 FS on sda7, internal journal
[ 11.368008] loop: module loaded
[ 14.734591] usb 1-1: [ueagle-atm] modem synchronization failed (may be try other cmv/dsp)
[ 14.734595] usb 1-1: [ueagle-atm] (re)booting started
[ 16.148047] firmware: requesting ueagle-atm/DSPep.bin
[ 16.381684] usb 1-1: [ueagle-atm] ATU-R firmware version : 44e2ea17
[ 16.381684] firmware: requesting ueagle-atm/CMVep.bin.v2
[ 16.397947] usb 1-1: [Ueagle-atm] requesting firmware ueagle-atm/CMVep.bin.v2 failed, try to get older cmvs
[ 16.397952] firmware: requesting ueagle-atm/CMVep.bin
[ 16.410115] usb 1-1: [Ueagle-atm] use deprecated cmvs version, please update your firmware
[ 16.450301] usb 1-1: [ueagle-atm] modem started, waiting synchronization...
[ 24.052731] kjournald starting. Commit interval 5 seconds
[ 24.052731] EXT3 FS on sda8, internal journal
[ 24.052731] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.412004] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 4000+ processors (1 cpu cores) (version 2.20.00)
[ 25.433366] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[ 26.052659] NET: Registered protocol family 10
[ 26.053080] lo: Disabled Privacy Extensions
[ 28.465302] usb 1-1: [ueagle-atm] modem operational
[ 28.588329] lp0: using parport0 (interrupt-driven).
[ 28.608504] ppdev: user-space parallel port driver
[ 29.722353] [drm] Initialized drm 1.1.0 20060810
[ 29.732370] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 29.732370] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 30.092005] PPP generic driver version 2.4.2
[ 31.319236] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 31.319254] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 31.319319] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 31.596211] [drm] Setting GART location based on new memory map
[ 31.596221] [drm] Loading R300 Microcode
[ 31.596285] [drm] Num pipes: 1
[ 31.596292] [drm] writeback test succeeded in 1 usecs
[ 45.548005] PPP BSD Compression module registered
[ 45.619751] PPP Deflate Compression module registered
[ 50.487532] fuse init (API version 7.9)
Czyli jak widać jest coś o EMU.

[ Dodano: 2009-06-13, 11:31 ]
No i co ?

Pomoże ktoś ?