ipw3945 instalacja bez ndiswrappera

m99 - 30-09-2007 18:15
Witam
Mam karte wifi ipw3945 w tym momencie uzywam tej karty za pomoca ndiswrappera jednak chcialbym sie przestawic na firmware dostarczony przez producenta poniewaz ndiswrapper to rozwiazanie "nieeleganckie".
Zainstalowalem ipw3945-firmware ,ipw3945d ,ipw3945-source i ipw3945-modules.
modprobe ipw3945 pokazuje
FATAL: Error inserting ipw3945 (/lib/modules/2.6.21-2-686/contrib/ipw3945.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error running install command for ipw3945 a dmesg daje ndiswrapper version 1.47 loaded (smp=yes)
ndiswrapper: driver netw4x32 (Intel,04/30/2007,11.1.1.11) loaded
ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
ndiswrapper (NdisWriteErrorLogEntry:192): log: 40001B7C, count: 2, return_address: f8dac5d2
ndiswrapper (NdisWriteErrorLogEntry:195): code: 0x56524457
ndiswrapper (NdisWriteErrorLogEntry:195): code: 0xdd
PCI: Setting latency timer of device 0000:10:00.0 to 64
ndiswrapper: using IRQ 17
wlan0: ethernet device 00:13:02:ae:e1:f9 using NDIS driver: netw4x32, version: 0x1000b, NDIS version: 0x501, vendor: 'Intel(R) Wireless WiFi Link 3945ABG Driver', 8086:4222.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
usbcore: registered new interface driver ndiswrapper
psmouse.c: TouchPad at isa0060/serio4/input0 lost synchronization, throwing 4 bytes away.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ndiswrapper (add_wep_key:798): adding encryption key 1 failed (C0010015)
ndiswrapper (add_wep_key:798): adding encryption key 1 failed (C0010015)
ndiswrapper (add_wep_key:798): adding encryption key 1 failed (C0010015)
ndiswrapper (set_essid:59): setting essid failed (00010003)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: no IPv6 routers present
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: no IPv6 routers present
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol escape_essid
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: Unknown symbol free_ieee80211
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol alloc_ieee80211
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol escape_essid
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: Unknown symbol free_ieee80211
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol alloc_ieee80211 Pozdrawiam

siewiex - 01-10-2007 19:39
Napewno ipw3945-modules zainstalowals dla swojej wersji jadra?
Jak dla innego to nie bedzie dzial. Jakiego masz laptopa? Bo u mojego kumpla FS Amilo v3505 wifi zaczelo normalnie dzialac dopiero po aktualizacji biosu ;-)

m99 - 01-10-2007 19:58
Mam lapka HP nx7400 ey508es .wszystko mam zainstalowane dla mojego jadra.

pavbaranov - 04-10-2007 09:15
Na pewno tam jest taka karta? Bo np. z http://r2d2.stefanm.com/nx7400.html wynika coś innego :) Jeśli dobrze rozumiem tego loga, to wygląda tak, jakbyś miał zainstalowane zarówno ndiswrappera, jak i sterowniki do Intela (z którymi jest problem). Jeśli pamiętam, to na którymś forum było, że te sterowniki chodzą dopiero od którejś wersji jądra (albo 21, albo 22, muszę to sprawdzić, ale nie mam w tej chwili czasu). 2.6.22-2 na pewno jest w sid/sidux dostępna.

fanatico - 04-10-2007 10:57
Chodza na 100 % na 2.6.21